Within “Get Support” page, you can find useful tip and tricks, firmware update and more information about your device usage and maintenance. Visit get support page!
Ensure whether the holder itself, is showing an error warning
1. Open the Pocket charger and take out the holder
2. Tap or lift the holder’s Touch Screen
3. Check if the holder itself is flashing the letter “E” 3 times
Is the holder itself flashing the letter “E” 3x? (Please note that, if you choose the option “YES”, this will take you to holder diagnostics. In this case please choose “Letter E flashing red 3x”
The contacts on the holder and Pocket Charger might need cleaning
If the contacts between your holder and pocket charger are not clean, this also doesn’t let your holder to charge fast enough and your holder status warns you with the red blinking Pocket Charger light 3 times.
Let’s perform cleaning:
Clean
the contacts on your holder and pocket charger
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown
When a firmware update is failed or being interrupted, the holder lights on the Pocket Charger might blink red 3x.
In case you are not in the process of updating your firmware, please select “ NO” and skip the below steps.
Let’s try updating your firmware again.
As every electronic device, IQOS is also built from two core elements – physical device items and the digital working instructions, called as firmware.
Firmware of your IQOS ILUMA i should be regularly updated for maintenance and improvement of your device performance.
Firmware update can be done through IQOS WebApp or visiting an IQOS Store.
IQOS WebApp is available both for desktop and mobile devices.
After trying firmware update again, is your device now working?
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 second.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown
When a firmware update is failed or being interrupted, the Pocket Charger light might blink red 3x.
In case you are not in the process of updating your firmware, please select “ NO” and skip the below steps.
Let’s try updating your firmware again.
As every electronic device, IQOS is also built from two core elements – physical device items and the digital working instructions, called as firmware.
Firmware of your IQOS ILUMA i can be regularly updated for maintenance and improvement of your device performance.
Firmware update can be done through IQOS WebApp or visiting an IQOS Store.
IQOS WebApp is available both for desktop and mobile devices.
After trying firmware update again, is your device now working?
• use the AC Power Adaptor from the previous IQOS devices
• purchase it separately in IQOS stores or on iqos.com
• use a 3rd party Certified AC Power Adaptor (with the safety certification mark)
Plug the AC Power Adaptor to your pocket charger and then to a wall power outlet for 135 min for full charge.
During charging, the strip lights on the pocket charger will pulse. Few seconds of charge should be sufficient for the yellow light to disappear and at least 1 light to turn solid white.
To check the level of charge of your device, briefly press and release the pocket charger button. For a fully charged device, all 4 strip lights should be solid white.
After these steps, did your pocket charger start to be charged?
1. Unplug the Pocket Charger and ensure the charging ports on both the pocket charger and the charging cable are dry and clean from contamination
2. Charge your device by using the AC power adaptor (sold separately) and cable for approximately 135 min, for full charge. 4 lights will turn solid white and then turn off when it is fully charged.
After these steps, did your pocket charger start to charge?
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 second.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown
After these steps, did your pocket charger start to charge?
1. Unplug the Pocket Charger and ensure the charging ports on both the pocket charger and the charging cable are dry and clean from contamination
2. Charge your device by using the AC power adaptor (sold separately) and cable for approximately 135 min, for full charge. 4 lights will turn solid white and then turn off when it is fully charged.
After these steps, did your pocket charger start to charge?
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 second.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown
After these steps, did your pocket charger start to charge?
1. Place the holder inside the pocket charger. Ensure to place it correctly.
2. Press the pocket charger button for 4 seconds to turn your device ON. Remember, the same action applies to turn it OFF as well. Turning OFF the pocket charger will also turn OFF the holder.
After these steps, did your pocket charger turn on?
1. Ensure the optimal charging for your pocket charger;
• use AC Power Adaptor from the previous IQOS devices
• purchase it separately in IQOS stores or on iqos.com
• use a 3rd party Certified AC Power Adaptor (with the safety certification mark)
Check the charging cable entrance of your pocket charger and the AC power adaptor one. Ensure they are clean and remove any blockage by gently blowing from distance.
Charge your device for approximately 135 min, for full charge. 4 lights will turn solid white and then turn off when it is fully charged
If the device is fully discharged, the Pocket Charger’s light might take few seconds before turning ON.
2. While your pocket charger is being charged, strip lights will be pulsing. Seeing a light on a deeply discharged pocket charger may take few seconds.
In case a light pattern appears on your Pocket Charger, leave the device to charge until at least 1 white light turns solid white (25% charged) and unplug the device.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Is the Pocket charger light ON, when button pressed ? (Please note that, if you choose the option “NO”, this will take you to another issue on pocket charger diagnostics. In this case please choose “No lights on pocket charger (short button press)”)
Ensure whether at least there is one solid white light on the Pocket Charger
Is the Pocket charger charged? (Please note that, if you choose the option “NO”, this will take you to another issue on pocket charger diagnostics. In this case please choose “Pocket charger status light blinking yellow 3x”)
The contacts on holder and Pocket Charger might need to be cleaned
Clean the contacts between your holder and the pocket charger
Let’s perform cleaning:
Clean the contacts on your holder and pocket charger
Place the holder back in the Pocket charger and close the Pocket Charger door
Leave the holder to charge for about 5 mins or until the first light turns solid white
Please note that in case the holder gets warm when trying to charge it, leave it to cool down and ideally, please visit an IQOS store to receive further support
After these steps, did you resolve the issue or are you able to visit an IQOS store?
• Use the AC Power Adaptor from the previous IQOS devices
• Purchase it separately in IQOS stores or on iqos.com
• Use a 3rd party Certified AC Power Adaptor (with the safety certification mark)
Plug the AC Power Adaptor to your pocket charger and then to a wall power outlet for 135 min for full charge.
During charging, the strip lights on the pocket charger will pulse. Few seconds of charge should be sufficient for the yellow light to disappear and at least 1 light to turn solid white.
To check the level of charge of your device, briefly press and release the pocket charger button. For a fully charged device, all 4 strip lights should be solid white.
After these steps, did your pocket charger start to be charged?
1. Unplug the Pocket Charger and ensure the charging ports on both the pocket charger and the charging cable are dry and clean from contamination
2. Charge your device by using the AC power adaptor (sold separately) and cable for approximately 135 min, for full charge. 4 lights will turn solid white and then turn off when it is fully charged.
After these steps, did your pocket charger start to charge?
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 second.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown
After these steps, did your pocket charger start to charge?
1. Place the holder inside the pocket charger. Ensure to place it correctly.
2. Press the pocket charger button for 4 seconds to turn your device ON. Remember, the same action applies to turn it OFF as well. Turning OFF the pocket charger will also turn OFF the holder.
After these steps, did your pocket charger turn on?
1. Ensure the optimal charging for your pocket charger;
• Use AC Power Adaptor from the previous IQOS devices
• Purchase it separately in IQOS stores or on iqos.com
• Use a 3rd party Certified AC Power Adaptor (with the safety certification mark)
Check the charging cable entrance of your pocket charger and the AC power adaptor one. Ensure they are clean and remove any blockage by gently blowing from distance.
Charge your device for approximately 135 min, for full charge. 4 lights will turn solid white and then turn off when it is fully charged
If the device is fully discharged, the Pocket Charger’s light might take few seconds before turning ON.
2. While your pocket charger is being charged, strip lights will be pulsing. Seeing a light on a deeply discharged pocket charger may take few seconds.
In case a light pattern appears on your Pocket Charger, leave the device to charge until at least 1 white light turns solid white (25% charged) and unplug the device.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Ensure whether at least there is one solid white light on the Pocket Charger
Is the Pocket charger charged? (Please note that, if you choose the option “NO”, this will take you to another issue on pocket charger diagnostics. In this case please choose “Pocket charger status light blinking yellow 3x”)
The contacts on holder and Pocket Charger might need to be cleaned
Clean the contacts between your holder and the pocket charger
Let’s perform cleaning:
Clean the contacts on your holder and pocket charger
Place the holder back in the Pocket charger and close the Pocket Charger door
Leave the holder to charge for about 5 mins or until the first light turns solid white
Please note that in case the holder gets warm when trying to charge it, leave it to cool down and ideally, please visit an IQOS store to receive further support
After these steps, did you resolve the issue or are you able to visit an IQOS store?
• use the AC Power Adaptor from the previous IQOS devices
• purchase it separately in IQOS stores or on iqos.com
• use a 3rd party Certified AC Power Adaptor (with the safety certification mark)
Plug the AC Power Adaptor to your pocket charger and then to a wall power outlet for 135 min for full charge.
During charging, the strip lights on the pocket charger will pulse. Few seconds of charge should be sufficient for the yellow light to disappear and at least 1 light to turn solid white.
To check the level of charge of your device, briefly press and release the pocket charger button. For a fully charged device, all 4 strip lights should be solid white.
After these steps, did your pocket charger start to be charged?
1. Unplug the Pocket Charger and ensure the charging ports on both the pocket charger and the charging cable are dry and clean from contamination
2. Charge your device by using the AC power adaptor (sold separately) and cable for approximately 135 min, for full charge. 4 lights will turn solid white and then turn off when it is fully charged.
After these steps, did your pocket charger start to charge?
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 second.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown
After these steps, did your pocket charger start to charge?
A- The customer might not be using the pocket charger fully charged
B- The device might be outside of the operating temperature
C- Customer’s pocket charger battery capacity might be degraded by time – which is normally out of warranty
COMMUNICATE:
The pocket charger is designed to charge your holder up to 20 experiences only when your pocket charger is FULLY Charged
20 experiences mean that 20 singles experiences or 10 double (back-to-back) experiences.
CONFIRM TOGETHER WITH THE CONSUMER:
1. Ensure that the charging ports on both the PC and the charging cable are clean and free from contamination. If not, charging will be slowed down and the time that the PC need to fully charged will be increased.
2. For safe use and optimal charging, you have three options (use AC Power Adaptor from the previous IQOS devices, purchase it separately in IQOS stores or on iqos.com, use a 3rd party Certified AC Power Adaptor (with the safety certification mark)
3. During charging, the strip lights on the pocket charger will pulse. If Pocket charger is fully discharged, the PC’s lights might take few seconds to turn on. A fully charge takes approximately 135 mins. The 4 strip lights will turn solid white and turn off when fully charged.
4. Once the PC is fully charged, use your holder as usual until the PC is fully discharged. Always use the device within the operating temperature (0 and 40°C), unless an experience could be interrupted.
5. After these steps, with a full charge, can the customer’s pocket charger charge the holder for up to 20 experiences?
DECIDE:
According to the above steps and the consumer’s claim, make the decision;
Option A: Customer’s pocket charger can charge the holder up to 20 experiences, therefore, DO NOT replace.
Option B: Customer’s pocket charger cannot charge the holder up to 20 experience. Proceed with the next step communication
Customer’s pocket charger battery capacity might be degraded by time – which is normally out of warranty
COMMUNICATE:
As any other electronic devices, the battery performance of the pocket charger reduces over time. This is a normal situation for a battery performance on electronics.
The device is rated to be used between 0 and 40deg C. If used outside, could stop an experience or affect battery life.
The reduced battery performance may affect the charging capacity of your pocket charger.
According to the electronics industry standards and our warranty terms, battery degradations are out of warranty.
However, our customer’s satisfaction is our top priority.
CONFIRM WITH CONSUMER:
Check whether there is a device failure, or battery degradation. Device failure means that the number of experiences provided by the PC to the holder (when device is fully charged) is suddenly dropped by multiple experiences. (e.g. when the number of experiences drop from 20 to 12)
Only replace the device if there is a sudden drop in number of experiences provided, as apposed to slow degradation
Choose eligibility, if there is a sudden drop on the experiences or not covered, if it is something gradual.
Within “Get Support” page, you can find useful tip and tricks, firmware update and more information about your device usage and maintenance. Visit get support page!
Cosmetic damage (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage (improper handling or liquid contact) or failure caused by normal wear and tear of your device are excluded from voluntary warranty program.
Our online store offers a wide range of accessories designed for IQOS ILUMA I that could help you minimize the impact of the cosmetic damage.
If you wish to speak to a Customer Care representative, please contact us at:
+62 (021) 1500 975
This product is not risk free and provides nicotine, which is addictive. Only for use by adults.
Bluetooth connection issues, cosmetic damages (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage or failure caused by normal wear and tear of your device are excluded from voluntary warranty and accidental damage coverage.
If you wish to reach a customer service representative, visit 'contact us' page to choose the channel of your preference.
Cosmetic damage (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage (improper handling or liquid contact) or failure caused by normal wear and tear of your device are excluded from voluntary warranty program.
Our online store offers a wide range of accessories designed for IQOS ILUMA I that could help you minimize the impact of the cosmetic damage.
If you wish to speak to a Customer Care representative, please contact us at:
+62 (021) 1500 975
This product is not risk free and provides nicotine, which is addictive. Only for use by adults.
Make sure both Charger and Holder are registered on your profile on iqos.com.
Make sure your holder is inside the pocket charger if trying to access the holder’s settings or updating the holder’s firmware.
Let’s follow these few steps to connect your mobile device to the IQOS WebApp:
1. Remove all devices, not only IQOS, from the Bluetooth settings of the respective end device.
2. Turn OFF Bluetooth on the phone/PC.
3. Turn ON back Bluetooth on the phone/PC again.
4. Turn OFF your IQOS and turn it ON again by pressing the pocket charger button for 4 seconds. This will instantly re-active Bluetooth of your IQOS device.
5. Log in to IQOS WebApp again and follow the shown steps.
If you are using web IQOS WebApp, clear your cache in the browser
If you are using an iOS device, make sure you launch the IQOS WebApp using the Bluefy browser.
Ensure that only one IQOS device is connected via Bluetooth.
If this does not work, try pairing your IQOS via USB on Mac or PC.
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds.
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, the lights will be shown after 4 seconds to indicate the device will turn ON or OFF. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds, until reset is completed.
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be showed.
After resetting, open the IQOS WebApp and follow instructions on the IQOS WebApp to add a device: the IQOS WebApp will explain how to enable Bluetooth and provides a step-by-step guide to connect
After these steps, is your device connecting properly now?
Bluetooth connection issues, cosmetic damages (such as scratches, dents, broken plastic, hairline cracks, discoloration), damage or failure caused by normal wear and tear of your device are excluded from voluntary warranty and accidental damage coverage.
If you wish to reach a customer service representative, visit 'contact us' page to choose the channel of your preference.
Overheating or plastic softening around the USB charging port/cable
[Knowledge only, NOT to communicate]
A- This can happen whilst charging only. It can also be described by the user as melting
B- This can be caused by contamination in the USB connectors that can interfere with the transmission of the current and cause overheating. Refer to Product Notification PN006 for further details.
COMMUNICATE:
Inform the customer that contamination such as fluff, dirt, dust or moisture in the USB connectors can interfere with the transmission of current from the AC power adaptor to the device and cause overheating.
Advice to let the device cool down before handling it.
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Overheating or plastic softening around the USB charging port/cable
[Knowledge only, NOT to communicate]
A- This can happen whilst charging only. It can also be described by the user as melting
B- This can be caused by contamination in the USB connectors that can interfere with the transmission of the current and cause overheating. Refer to Product Notification PN006 for further details.
CONFIRM TOGETHER WITH THE CONSUMER:
1. Ask to clean or dry the USB port of the PC.
Suggest to not use metal tool to clean the device in order to avoid damaging it.
Within “Get Support” page, you can find useful tip and tricks, firmware update and more information about your device usage and maintenance. Visit get support page!
Overheating or plastic softening around the USB charging port/cable
[Knowledge only, NOT to communicate]
A- This can happen whilst charging only. It can also be described by the user as melting
B- This can be caused by contamination in the USB connectors that can interfere with the transmission of the current and cause overheating. Refer to Product Notification PN006 for further details
CONFIRM TOGETHER WITH THE CONSUMER:
Ask to clean or dry the USB port of on the charging cable.
Try charging your Pocket Charger again. Do not leave the PC unattended for the first few minutes of charge to check for potential overheating
Accidental Damage is a free of charge service for our customers. It is offered as a support to replace the products which lost the functionality, after being subject to the damages that are not covered by voluntary warranty (e.g. drops, contacts with liquids or abrasive agents)
If your device is eligible, we will place a replacement order for you!
Place the holder in the Pocket Charger. Ensure to place it correctly.
Press and hold down the ON/OFF button on the Pocket Charger for 10 seconds until status lights fade out
Please note: If your IQOS ILUMA i is turned OFF at the time of RESET; when pressing the button, after the first 4 seconds, the device will turn ON and lights will fade in. In order to perform the RESET correctly, it is important to keep the button continuously pressed for 10 seconds
2. RESET is confirmed when status lights fade in, blink twice fast, ramp up and then the current device charge level will be shown.
As every electronic device, IQOS is also built from two core elements – physical device items and the digital working instructions, called as firmware.
Firmware of your holder and pocket charger should be regularly updated for maintenance and improvement of your device performance.
Firmware update can be done through IQOS WebApp or visiting an IQOS Store.
IQOS WebApp is available both for desktop and mobile devices.
Please confirm you are an adult user of nicotine products aged 21+
Please confirm you are an adult user of nicotine products aged 21+
Please confirm you are an adult user of nicotine products aged 21+.
Are you an adult nicotine product user over 21 years old?
Sorry! This website is intended only for users of nicotine or tobacco products who are over 21.
This website contains information about smoke-free product, and we need your confirmation that you are an adult user of nicotine products to make sure that you are an adult in Indonesia who would otherwise continue to use nicotine products.
Country redirect
Please note this site is intended for Indonesia. In order to ensure compliance with local legal requirement, we need to redirect you to your country of origin..
